The purchased materials should not be stored in the open air. After the materials are transported into the construction site, a layer of clear oil should be applied to the surface, also called sealing oil treatment to prevent wind cracking and deformation. After the decorative panel is shipped to the site, use a dry towel to wipe off the dust, apply the varnish cover twice in a row, and all the decorative panels should be laid flat. Place a blockboard on the bottom of the decorative panel and press one on the panel. A blockboard that keeps the board flat.
1. Wood articles: oil sealing treatment to prevent wind cracking
The purchased materials should not be stored in the open air. After the materials are transported into the construction site, a layer of clear oil should be applied to the surface, also called sealing oil treatment to prevent wind cracking and deformation. After the decorative panel is shipped to the site, use a dry towel to wipe off the dust, apply the varnish cover twice in a row, and all the decorative panels should be laid flat. Place a blockboard on the bottom of the decorative panel and press one on the panel. A blockboard that keeps the board flat. Do not put the panel upright, which will cause the panel to crack and rise.
2. Putty articles: the time and extent of opening the window are particular
Walls and ceilings should be naturally dry if you put on putty or wallpaper. Do not open doors and windows to prevent rapid water loss and affect construction and deformation. The time to open the window is also very particular: it is best to choose between 10 am and 4 pm, the temperature is relatively high during this period, which can prevent the new scraped putty from freezing. The correct method for scraping the putty is to wait for the first time the putty is completely dry, and then scrape the putty for the second time; the second time the putty is completely dried and then carefully sanded with sandpaper. It is best to put all the sand gray walls and thermal insulation walls on the cloth, and put the putty directly on the cloth until it is dry and sanded with sandpaper. If there are large holes or recesses on the wall, it is best to use gypsum powder and latex to blend the wall. When there is a large crack in the wall, the crack should be attached with kraft paper and then putty putty. When the area is large, it is best to stick the cloth and then put the putty, so as to prevent the wall from being flat and not cracking.
3. Coating articles: the construction environment temperature is the most important
When the painter sprays various paints, it should be applied strictly according to the temperature in the product description. Under normal circumstances, the ambient temperature of the coating application should not be lower than 5 ° C; among them, the commonly used mixed color coating application should be at an ambient temperature of 0 ° C or higher, and the ambient temperature when the varnish is applied is not lower than 8 ° C. The oiler's work should pay more attention to "warm", and then open the doors and windows to ventilate after fully drying.
4. Accessories: Do not contain ice in the mortar, do not open the cement in the open air
The sand used in the construction should be carefully screened and must not contain ice. When mixing the mortar, the temperature of the water must not exceed 80 °C. If the decoration requires cement, it is best not to open the construction in the open air, and the construction site should also pay attention to the insulation.
5. Heating articles: heating starts, prohibition of dismantling
In the home decoration, people pay more and more attention to the aesthetics of the heating equipment in the living room. The heating of the original cast iron gradually fell out of favor. Many people are replacing the new radiator in the decoration. Therefore, consumers should buy radiators from regular manufacturers and have them installed by professional installation teams. After entering the heating period, the heating water supply has been pressurized. If the construction is slightly improper, it is easy to cause a "running water" accident, resulting in irreparable damage. Therefore, after the start of central heating, the heating pipes and radiators are strictly prohibited from being replaced and replaced.
6. Outside window articles: cement mortar should be tightly sealed, and the sealing strip should not be too tight.
The installation of plastic-steel windows has also become a common item for decoration. First of all, the replacement of the outer window must be fixed firmly. Even if it is slightly inclined, the future push-pull opening of the window will become a problem, and the rain will also seep into the rain. Secondly, the cement mortar around the closed outer window must be tightly sealed. Otherwise, in the coldest winter, the northwest wind will blow, and the warmth of the room will also decrease. Again, the sealing strip of the plastic window should not be sealed too tightly. The rubber seals used in plastic-steel windows have thermal expansion and contraction, which will be tightened to some extent during winter installation, and will expand after heating in the hot summer.
7. Fire prevention articles: Fire extinguishers should be installed at the construction site.
Winter decoration must pay attention to, can not use fire on the construction site, electric heating equipment, gas pipes for cooking, spray lamps for waterproofing, etc. should be used with caution, and fire extinguishers must be placed on site.
8. Contamination articles: substances such as formaldehyde and benzene are released from paints and rubbers.
The winter weather is cold. During construction, workers are used to tightly closing doors and windows, which can easily cause indoor air pollution poisoning. Especially in the decoration process, when applying waterproof layer, when using glue products, paving the floor and painting, there will be a lot of formaldehyde and benzene substances harmful to the human body in the air. These substances are ventilated through the window to be volatilized, otherwise it will Deposited in indoor air, the concentration is getting bigger and bigger. Therefore, not only the window ventilation should be opened during the decoration process, but also the window ventilation should be paid after the decoration. It is best to use it normally about two months after the completion of the project.
The art candle is in varies shape,like fruit shape,human shape,flower shape,animal shape,image shape and so on. The candle shape also can be customized. Art Candles are made by paraffin wax and they are usually used in birthday party, wedding, general party,etc.
Total area: 20,000 square meters
Fixed assets:RMB 10 million
Total empolees: 260
Facility: 500
Production Capacity: 1800MT/Month
We mainly produce White candle, Bright candle, Tea-light candle, Spiral candle, Church candle, Taper candle and Gift candle. By the high quality and competitive price, our goods find a very good market in Africa, the Middle East,Southeast Asia, Europe, and South America, in more than 30 countries and regions.
Keeping the principle of "Customer first; reliable service", we are doing every effort to thank good cooperation and great support from our customers with our continuous process, good products, competitive price and circumspect service.
Looking forward to establish business with you.
Art Candles
Art Candles,Decoration Art Candles,Wedding Art Candles,Art Candle With Lacker
Hebei Huaming Laye Limited Company , https://www.huamingcandle.com